Back

Oil sands crude — profits and problems?

Canadian bitumen production currently runs about 1 MMbpd, with some being sold as Synbit and Dilbit. Over the next 10-12 years output is expected to increase to 3.5 MMbpd and more refiners will begin investing to process it and come to depend on the Synbit and Dilbit for a significant part of their supply. Few today, however, have ever processed these feeds at high blend ratios, and are unaware that conventional process and equipment designs are not up to the job. Canadian oil sands to desalt, difficult to vaporize, thermally unstable, corrosive, and produce high di-olefin product from the coker. If you intend to lock into a long-term supply, therefore, it is imperative that you consider reliability and run length from a particular design.

Too low tube velocity in the vacuum heater tubes will lead to precipitation of asphaltenes. Too fast a flow rate will erode the tube bends. If coil layout, burner configuration and steam rate are not correct, run length will be measured in months, not years. Diluent recovery unit designs must take into account possible upsets from water slugs and other unpredictable situations that have damaged internals, resulting in diluent losses and high vacuum unit overhead condensable oil. Diluent is neither cheap nor plentiful, and high vacuum column operating pressure will reduce overall liquid volume yields. And if the design of the delayed coker fractionator is based on today’s experience with conventional heavy feedstocks you will be lucky to run six months.

What all this means is that special process and equipment designs are needed to satisfy the special demands of processing oil sands crudes. Such processes are not generated by computer based designers who have little or no experience and never leave the office. They are developed only by engineers with know-how who have real experience wearing Nomex® suits and measuring true unit performance in Northern Alberta. Shouldn’t this be kept in mind by those considering long term supply agreements?

DOWNLOAD LITERATURE

Sponsor:

Process Consulting Services

Categories:

Oil sands crude — profits and problems?

Canadian bitumen production currently runs about 1 MMbpd, with some being sold as Synbit and Dilbit. Over the next 10-12 years output is expected to increase to 3.5 MMbpd and more refiners will begin investing to process it and come to depend on the Synbit and Dilbit for a significant part of their supply. ...
Nasty stuff

Heavy crudes are here to stay. As longs as oil prices remain high, Canadian, Venezuelan, Deep Water Gulf of Mexico, Mexican and other low API gravity crude oils will play an ever more important role in supplying world refineries. And prices promise to remain high because gainsayers notwithstanding, Hubbert ...
Designing deepcut vacuum units that really work

Every barrel of vacuum gas oil (VGO) you can save from being reduced to coke in the delayed coker unit is a barrel more that can go to the FCCU. That’s a good reason to raise HVGO cutpoint. But how to do it? Some people think the job can be done just by running computer models in the engineering ...
A time for grass roots thinking ?

Within the past year or two spiking crude prices and surging refinery margins have led to overheated talk about increasing refinery capacity worldwide. Plans for construction of as many 60 grass roots refineries have been discussed. But stretched out lead times for major equipment and inflated prices, ...
A single integrated vacuum system

Failure to design the vacuum unit as an integrated system will invariably result in unsatisfactory yield and poor product quality (high vanadium, nickel, microcarbon, or asphaltenes), and ultimately, an unscheduled shutdown. To avoid these revamp problems the charge pump, fired heater, transfer line, ...
Is pinch enough?

Back in the late 1970’s and early 1980’s when fuel gas prices were high, energy utilization assumed major importance. A new method of calculating heat exchanger networks was developed. It was called Pinch Technology. Today pinch has been rediscovered by engineers who have access to fast computer ...
Opportunity knocks

A group of interesting articles* deals with opportunity crudes, a mixed breed that includes very heavy, sour and high total acid number types as well as those with unexceptional naphthenic acid content but which do have significant concentrations of aliphatic acids or possess the ability to generate ...
Processing heavy Canadian crude

Reducing crude oil cost is the major incentive driving crude and vacuum unit projects to handle heavy Canadian crudes. But such crudes–Albian Heavy, Christina Lake, MacKay River and others derived from oil sands–today present refiners with a unique set of problems not just because of extra-low ...
Why do many crude/vacuum units perform poorly?

In many cases it’s because the original design was based more on virtual than actual reality. There is no question: computer simulations have a key role to play but it’s equally true that process design needs to be based on what works in the field and not on the ideals of the process simulator. ...
Why produce diesel from the vacuum unit?

Look ahead five years. The economy is likely to keep tightening and the rush to control pollution will inevitably be accompanied by demands for greater energy conservation. Consequence? A growing market for diesel which yields more energy per unit volume. Yet many continue to believe that producing diesel ...